SIMPLIFY
INSTALLATION OF OUR MOST POPULAR DELAY BOXES WITH A MOUNTING KIT!
- Model
CC1DMK
- A
simple, inexpensive time saver for flush mounting with any CC1, CC2, CC3, BM1,
BM2 or NOC1 in to a 1/8" to 1/4" thick dashboard or panel. This mounting
kit includes a handy template and all needed screws, washers and standoffs. Fits
both popular units.
- Model
L1DMK
- Flush
mount your Lightning easily with this inexpensive, time saving kit. Works with
both L1 and L2 models. Includes all needed screws, washers and standoffs for mounting
into an 1/8 to 1/4 inch thick dashboard panel.
- INSTALLATION
KIT- Model
IK
- Designed
as an engineered system for the RTD7, CO2, SCO1, CC3, L1, L2 and T1 this complete
kit can be used to easily and correctly install any type of delay box. Includes
a heavy duty, quick acting, precision release transbrake switch with bracket and
adjusting lock nut; heavy duty, 14 gauge stretch cord; 10 foot lengths of 14 gauge
wire; 15 foot length of 12 gauge wire; fuse with in line holder; wiring connectors;
terminals; mounting screws; 25 nylon wire ties; and a detailed wiring diagram.
- PRECISION
TRANSBRAKE BUTTON - Model PBSRTD
-
Heavy duty, precise button allows full current to reach the transbrake solenoid.
1/2-inch diameter button can be adjusted up and down to suit driver feel. Only
100th of an inch release travel (half the travel of other buttons!) for quick
and consistent reaction times.
- EXTRA
LARGE TRANSBRAKE BUTTON - Model
PBSXL
- The
same precision button as above, but with a 1-inch diameter adjustable travel button.
Great for delay boxes that have multiple shots at the tree.
-
- PUSHBUTTON
SWITCH- Model PBSTS
-
This heavy duty unit is single pole, double throw with brass terminals. Can be
used for brake pedal switch or even a wide open throttle switch.
- STRETCH
CORD- 2 CONDUCTOR - Model SC2
- Super
large 14 gauge, multi-strand conductors. Coil is only 1 foot long when contracted,
and stretches over 10 feet when needed. We used larger 14 gauge wire to prevent
massive voltage drop that the small 16 and 18 gauge coil-cords cause. Typically
less than half the voltage drop when compared to other "heavy duty"
cords!! Ready to be attached to your existing button or our PBSRTD and PBSXL buttons
above. Dark Blue vinyl jacket stays clean after years of use.
-
- STRETCH
CORD - 3 CONDUCTOR - Model SC3
- Three
conductors? Why? Let's say you want to mount your transbrake button and your line
lock button on the steering wheel... both buttons need power supplied to them
right? The SC3 has 1 super large 12 gauge wire to bring power "up" to
the both buttons, then use one of the 14 gauge wires to bring the transbrake button
signal "down" and the other 14 gauge wire to bring the line lock button
signal "down". This is a lot cleaner and less expensive than running
2 coil cords! Medium Red vinyl jacket stays clean after years of use.
-
STRETCH
CORD - 4CONDUCTOR - Model SC4
- The
new 4 wire heavy duty stretch cord from Dedenbear is the solution to running multiple
buttons on your steering wheel. It has two 14 gauge and two 18 gauge leads for
running up to 3 different switches on the wheel. It has a tough, gloss black outer
sheath that will last for years. The cord will stretch to well over 10 feet.
- TOGGLE
SWITCH - Model TSWRTD and
Model TSWDPRTD
- (double
pole, double throw)
- A premium
quality toggle switch. We package the same unit with each delay Box. Single pole,
double throw (on-on) can be used as normal on-off switch too. Screw terminals
on the back keep your wires from slipping off. 25 amp rating. TSWRTD -
TSWDPRTD -
- LEVER
SWITCH - Model LSW
-
- "Micro
Switch", Roller tip lever switch. Single pole, double throw.
HIGH
POWER RELAY - Model HPR-
- A high
quality 12 volt, 5 terminal Bosch relay rated at 30 amps. Comes complete with
crimp on terminals and slip on relay base. Can be used normally open or normally
closed.
75
AMP RELAY - Model BAR-
- High
quality 12 volt 4 terminal Bosch 75 Amp relay. Built in mounting brackets, screw
terminals. Normally open contacts.
Only
Back
to the top
-
-