|
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | |
| | | | | | |
| | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | |
| | | | | | | | |
WP1 & WP2 FEATURES: | | | | |
| | | | | | | | | | |
- WP1 and WP2
units weigh only 4.0 and 4.2 pounds, and are just 4-1/4-inches deep.
- Draws
only 3-1/2-amps at 12 volts - half the draw of conventional electric pump drives.
- High-speed,
centrifugal impeller flows an incredible 25 gallons per minute! (when used with
a 1-3/4" hose. AN adapters will significantly decrease efficiency.)
- Tested
up to 250 degrees Fahrenheit and 30 psi.
- Works
with 12 or 16 volt systems (higher flow at 16 volts).
- Premium
quality, custom built motor features ball bearings, high temperature armature
windings, and a stainless steel shaft.
- One
piece aluminum casting
- Single
gasket design and custom shaft seal ensure leak free performance.
- Designed
to clear belt drive camshafts.
- Threaded,
three-in-one water inlet included. Accepts either 1-1/4 inch or 1-3/4 inch hose,
or 1 inch pipe thread.
- Easily
rebuildable; all internal parts are interchangeable between big block and small
block models
| |
| | | | OUTPERFORMS
ALL OTHERS! Dedenbear
Cool Pumps have helped win multiple NHRA national events, plus two Winston world
championships. The
smallest, lightest, highest volume electric pumps available. Specifically engineered
for the types of engines, radiators and radiator placements used by drag racers.
These are the shortest pumps in the industry - ideal for dragsters and cars with
minimal radiator clearance. | | | | | |
| | | | | | | | | | | | | | |
- Model
WP1 Water Pump- - Electric, Engine Mounted, Small
Block Chevy
-
Model
WP2 Water Pump - Electric, Engine Mounted, Big Block
Chevy
Model WP3 Water
Pump- Electric, Remote Mounted, Universal Application | | | | |
| | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | WP3
FEATURES | | | | | |
| | | | | | | | | | | | | | | | | | | | | |
- This rebuildable
design features a hard anodized, billet aluminum impeller and custom seal tested
at 250 degrees. Unlike rubber impeller RV and boat units now in use, which seize
at 140 degrees.
- Inlet
accepts either 1-1/4 inch hose or 3/4 inch NPT; the outlet is 3/4 inch NPT.
- Works
with 12 or 16 volt systems.
- Runs
quiet.
- Back
of casting is already drilled and tapped for mounting bolts.
- Can
be used with our WH1 and WH2 water headers for Chevrolet
applications.
|
| | | | | | | | | | | | | | | | | | |
Model
WP3 is the ideal remote mount electric water pump for any type of dragster
or roadster engine. This universal pump weighs just 3-1/4 pounds and draws
only 3 amps - yet pumps 23 gallons per minute! It can be mounted in any position.
| |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | |
- Model
ETC Expansion Tank Cap - Replacement
16lbs Radiator Cap for ET1
- Model
MTRWP Motor - Water Pump Replacement Motor for WP1,
WP2, WP3
- Model
SKWP Seal Kit - Water Pump Rebuild Kit for WP1,
WP2, WP3
| | |
| | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |